Noborizaka Fit USD/JPY

Currently, we are in the process of creating product descriptions. We will update them as needed, so please wait a moment.

This is a Nampin Martin EA equipped with an automatic fit function for the Nampin width. To mitigate the bankruptcy risk associated with Nampin Martin EA, it includes the following features.

• Automatic fit function for Nampin width
• Entry stop during market fluctuations
• Configurable loss cut logic
• Trend following of higher time frames
• Function to expand Nampin width
• Function to close half of the Nampin

The maximum drawdown in backtesting over 11 years from 2014 to 2025 is approximately 13.16% ($1,818).

⛀Automatic fit function for Nampin width

It is equipped with an automatic fit function for Nampin width based on ATR. Since the Nampin width is determined from the ATR ratio, specifying the Nampin width is unnecessary (minimum and maximum values can be set). Additionally, the profit-taking width is also calculated from the Nampin width.

⛀Setting Nampin multiplier

You can set the Nampin multiplier, allowing for fine lot adjustments. The default is 1.2 times.

Guideline for lot numbers

With a Nampin multiplier of 1.2 times and a maximum position count of 18.

Maximum lot = 1.26 lots (one side)

⛀Function to expand Nampin width

It is possible to expand the Nampin width as the number of Nampin increases. You can specify the number of positions at which to start expanding the Nampin width and the expansion amount (Pips).

If the original Nampin width was 20 Pips with the above settings

⛀ATR filter

If it exceeds the set ATR value, new position acquisition will be stopped. In the default setting, when the ATR of the hourly chart, period: 3 is "0.4" or more, new positions will not be acquired.

⛀Bollinger Bands filter

If the current value exceeds the upper limit of the Bollinger Bands, new sell entries will be stopped, and if it exceeds the lower limit, new buy entries will be stopped. The period and standard deviation of the Bollinger Bands can be set. The default settings are as follows.

If the current value is above BB's +2α

Stop new buy entries

If the current value is below BB's -2α

Stop new sell entries

⛀Trailing Stop functionTop function

When the average acquisition price of Nampin becomes positive, by using the trailing stop function, it is expected to secure a certain profit while additionally gaining profit. A trailing order will be placed against the average acquisition price of Nampin.

⛀ATR trailing function (Ver1.01 and later)

This function automatically updates the trailing stop value range based on the ATR value. (Default is not used)

To use this function, the parameter for "trailing stop function" must also be set to "true". The following parameter settings for the "trailing stop function" will also be inherited by the ATR trailing function.

• Trailing order update time (seconds)
• Trailing order update Pips
• Start position count for trailing

⛀Configurable loss cut logic

You can set loss cuts based on daily moving averages, the highest/lowest prices over the past XX days, and ATR values. In the default setting, loss cuts will be executed under the following conditions.

Buy loss cut criteria

• Short-term MA (20EMA) is below long-term MA (60SMA)
• Current value is below the lowest price over the past 90 days
• ATR is 0.5 or more

Sell loss cut criteria

• Short-term MA (20EMA) is above long-term MA (60SMA)
• Current value is above the highest price over the past 90 days
• ATR is 0.5 or more

⛀Early loss cut function

- Loss cuts will be executed when the short-term trend reverses while the number of positions is low. The determination of the short-term trend reversal is done by internal logic (not disclosed). If the ATR is smaller than the specified ATR value, loss cuts will not be executed.

⛀Trend following of higher time frames

In the default setting, the short-term EMA (period: 20) and long-term SMA (period: 60) of the daily chart are used, and when the short-term MA is above the long-term MAonly buyswill be executed, and when the short-term MA is below the long-term MAonly sellswill be executed. The periods can be set.

⛀Temporary entry stop function after execution 

New entries will be stopped for a specified time (minutes) after the entry is executed.

⛀Loss amount specified loss cut function

If losses exceed the specified amount, all positions will be closed. (Default is false: not used)

⛀Speeding up backtesting and reducing load measures (Ver1.02 and later)

By processing every specified number of seconds instead of every tick, it speeds up backtesting and reduces the load on the PC or VPS server running the EA.